Position Control Units Omron CS series

Position Control units Omron CS-series are the special unit of Omron PLCs CS series to control Servo driver or Stepping motor in making position. This position control units. This position control units usually also called by the  name NC units. NC units have a primary function as pulse generator that is used to drive the servo driver or servo motor controller.

The main convenience of NC units are all positioning parameters can be done with the program through the work area and data memory area (DM).

IAI Robo Cylinder

IAI Robo Cylinder is as an alternative to pneumatic cylinder that have many weakness. It has been discussed a litle before, pneumatic cylinder has a limited movement. With this robot can be obtained the movement by smooth and rapid or even without a beat at all.
Robo cylinder is normally used in simple application with sinle axis. The application is usually a linear application and moving from point to point. 

Connecting GP3000 with Omron PLCs C/V Series

To connect the Digital Proface GP3000 with Omron PLCs C/CV series, required setting of communication parameter between them. Two kinds of software needed to perform these setting.

1. Omron CX Programmer, to set the PLC communication parameter.
2. GP-Pro EX, to set GP3000 series communication parameter.

PLC type to be used as an example is the Omron C200HG. Communication will be done via the RS232C port on the CPU unit.

Digital Proface GP3000 Series

GP3000 Series by Proface

Graphic operator interface GP3000 is HMI or the touch screen is manufactured by Proface. GP3000 comes with the major features such as Video input interface, USB, Sound input, Various communication, video unit, ethernet interface, CF card, and serial communication.
Referring to what is required by the user, GP3000 is devided into four class. Classes are devided based on the features or facilities that exist in each class of GP3000. 

Memory Area of Omron CP1H PLCs

Memory area of PLC is the allocation of internal memory PLC that is accesible to be used as an operand of an instruction. Before learning the PLC programming technique. For PLC programmer, understanding the memory area of PLC is a must.

In this chapter, Omron CP1H is used as the example. This is fairly representative, due to the other series is similar. Likewisw for the other brands are basically the same principle.
In the memory area of Omron CP1H consists CIO area, Work area(W), Holding area(H), Auxiliary area(A), DM area(DM), Timer(T), Counter(C), Task flag area(TK), Data registers(DR), Index registers(IR), Condition flag area, and Clock pulse area.

Omron Modular PLCs Series

This type of Omron Modular PLCs is widely used as a machine control because It is middle PLC which is expandable both input-output and functions. It is flexible of Omron Sysmac with easy structure arranged on backplane. However, there are several PLCs are connected with backplane-free structure between CPU and modules so it is not necessary the backplane.

Unlike the model of Omron Micro PLCs, modules can be added as needed through a backplane or backplane-free structure.The modules could be positioning, analog, communication, counter, standard I/O and so on.

Omron Micro PLCs Series

In this chapter will be described on the category of Omron PLCs. Omron PLCs are classified based on the capabilities or features, as well as the capacity of input-output (I/O). This chapter will start for the first category is the Omron Micro PLCs. And regarding the other categories will be discussed in subsequent chapters.
Omron Micro PLCs is a type of Omron PLC which is the smallest category. There is limited ability or features as well as the number of input-output (I/O), when compared with others type.

Wiring Connection of PLC

CP1H PLC by Omron

This chapter will explain about how to make wiring connection on PLC circuit. And as an example, will be used Omron micro PLC CP1H series.

Numerical System in PLC

Numerical System in PLC is numbers or system numbers used by the PLC in performing logic operation.

Numerical Sytem in PLC

POPCOM Windows for Yamaha Robot

POPCOM Windows is software for Yamaha robot. With this software we can create, editing program, point position teaching an so on.

YamahaVIP Plus Software

VIP Plus is window based application to control Yamaha robot RCX series controller. This software was used to create the program, parameters, point position, monitor and manual running via these software.

Controller type: The RCX series controllers that can be controlled by this software are RCX40, RCX142, RCX143, RCX144, RCX221, RCX222, RCX240.

Omron CX-One

CX-ONE is released by Omron is an integrated software tool that can be used for all Omron PLCs and components. Thus, with just one software CX ONE, can be used for setting PLC, touch screen, servo, positioning, temperature, networking and so on.

Automation With Robot

Robot is intelegent mechanical device or system that can perform tasks or high precision motion based on programs that have been made.

Color Sensor

Color sensor is a sensor that is used to detect the color of an object.

This color sensor as actually a photo electric sensor that has a special character combination of color red (R) green (G) and blue (B). For that reason, color sensor often called the RGB color sensor. 

Floatless Sensor

Floatless sensor or Floatless switch is the sensor to detect level of liquid which is detected through electrodes submerged in the liquid.

Proximity Sensor

Proximity Sensor is a sensor to detect the object without touching the object being detected. The detected object can be either metal and non metal.

Temperature sensor

Temperature sensor is a sensor to detect the temperature of an object or room. 

Temperature sensors are very widely used both in industry and daily life due to temperature or thermal parameters are very influential in the process.

Encoder for Position Detection

Rotary Encoder is a sensor or device for detecting the direction of rotation, the angle position, and rotational position. 

Limit switch sensor

Limit switch sensor is one of the earliest type of sensor that work mechanically. This sensor basically a switch that can be in a state of ON or OFF as a result of mechanical movement.

Limit switches are basically formed from basic switch are then packaged in single unit to be used in accordance with particular application.